top of page
Cold storage Panel Systems

Cold storage Panel
Systems

Cold storage panel system is the perfect solution for food processing facilities, warehouses, and controlled temperature applications. These insulated panels are designed to withstand internal / external temperature differences of up to 80° C and suitable for external wall, partitions & ceilings. 

dc35db281d015af560a1.png

COOLERS AND FREEZERS

06c9803535a47bed4f2c72693b8510e8.png

MW CH

NEW panel with a refrigeration lock - mineral wool core.

​

MW CH wall panels with visible fastening are intended for external and internal walls on a skeleton structure. Steel sheet galvanized on both sides according to EN 10346 and coated with an organic polyester coating with a coat thickness of 25 μm is used as facing. The panels can be installed both in a vertical and horizontal arrangement. They ensure maximum fire protection and excellent sound reduction

​

890.jpg

insPIRe® CH MAX

NEW! Polyisocyanurate cooling panel

​

insPIRe®  CH MAX cooling panel is designed for walls and ceilings in rooms with reduced temperature, i.e. in cold rooms (t> 0 °) and freezers (t <0 °) and other facilities with controlled temperature and humidity. The panels can be used to erect free-standing buildings and make cold rooms or freezers inside existing buildings. The panels can be mounted both vertically and horizontally as single and multi-span elements.

​

book-104.png

MODULE WIDTH

THROUGH-FIXING PANEL:  1000mm and 1140mm

PROFILES

EXTERNAL SIDE:  Linear, Microfiltered, Wavy, Grooved, Flat

INTERNAL SIDE:  Linear, Flat

COLOURS

STANDARD EXTERIOR LINING COLORS 

RAL 7016

RAL 9002

RAL 9006

RAL 9007

RAL 9010

STANDARD INTERIOR LINING COLORS 

RAL 9002

RAL 9010

USAGE

EXTERIOR WALLS OF THE COLD STORE / FREEZER 

1223.png
122234.png

  1.      insPIRe® CH sandwich panel

  2.      Construction screw

  3.      Polyethylene sealing tape (PES)

  4.      Flashings between plates and foundation

  5.      Plate flashing

  6.      Construction of the object

Dedicated sandwich panels with a specially designed lock marked with the insPIRe® CH symbol ensure achieving high thermal insulation of the whole partition by significantly reducing the thermal bridges on the longitudinal joints of the panels. In addition, the use of plastic fasteners and careful filling of transverse joints with low-pressure polyurethane foam guarantees meeting the requirements for freezing walls.

  1.      GS insPIRe CH® sandwich panel

  2.      Polyethylene sealing tape (PES)

  3.      Flashing the connection of panels with the foundation

  4.      Construction of the object

12235.png

COLD STORAGE / FREEZER CEILING

  1.      insPIRe® CH sandwich panel

  2.      Construction screw

  3.      Polyethylene sealing tape (PES)

  4.      Plate flashing

  5.      Flashing the connection of panels with the wall

  6.      Low-pressure polyurethane foam

  7.      Ceiling construction

FLOOR ON THE GROUND - COLD STORE / FREEZER FLOOR INSULATION

  1. Concrete screed

  2. Cut-off layer, e.g. construction foil

  3. termPIR® AL thermal insulation panel with FIT cutter

  4. Damp layer, e.g. roofing felt / waterproofing foil

  5. Concrete underlay

  6. Aggregate foundation

Thanks to high thermal insulation and compressive strength of 150 kPa, term PIR thermal insulation panels can be successfully used to insulate plots in cold rooms and freezers, where, in addition to very good thermal insulation, adequate compressive strength is also required.

456.png

The graphic shows one of the possible solutions. If you have questions about other possible applications, please contact our Sales Manager.

COMPLEMENTARY PRODUCTS

GASKETS AND OTHER ACCESSORIES

  • Gaskets for sandwich panels 

  • Sealing flanges intended for passage of ducts (e.g. ventilation) through the casing made of sandwich panels

  • Bushings - washers for cold plates

We supply adhesive, polyurethane (PUS and PURS), polyethylene (PED) and butyl sealing tapes

akcesoria-uszczelki_03.jpg

SELF DRILLING SCREWS:

  • for hot rolled construction (wall thickness from 3 to 12 mm)

  • for cold-bent construction (thickness from 1.5 mm to 5 mm)

On special order it is possible to provide caps or connectors in the color of the outer cladding of the sandwich panel. Panels can be joined to steel, reinforced concrete and wooden constructions using dedicated fasteners. Detailed information on connectors can be found in our technical catalogues.

akcesoria-wkrety_03.jpg

FLASHINGS

  • Length: 3000 mm or 6000 mm

  • Material: galvanized steel sheet

  • Protective coating: polyester varnish

  • Additional protection: foil

Manufacturer has a profiling machine that allows bending of 1.25 mm thick sheet metal (maximum length of 6 m), in typical shapes from the catalog and according to the individual design of the customer. Detailed information on sheet thickness and colors can be found in the catalog dedicated to a specific panel.

The flashings are protected against damage by foiling the top side. Detailed data is available in the section "For designers - flashing"

Steel flashing are part of the insulation panel system - Sandwich Panels.
Additionally, they are used as a separate decorative element.

Steel flashing is made of galvanized metal sheet with a thickness of 0.5 mm, 0.7 mm and 1.0 mm, colors according to the RAL palette.
Standard length of metal flashing sheet is 6.0 m.

234.png

Contact us for detailed information regarding specific panel thickness, span and type of application. 

bottom of page